When our crew walked into that Milton, MA bathroom, the tile work was already done — beautiful white marble running floor to ceiling — and the homeowner had been waiting a few weeks to see it all come together with glass. That’s a pretty common scene for us in the spring; renovations that started over the winter finally hitting the finish line. Being present for every install we do, we’ve learned that no two openings are exactly the same, and the way you set the shower door hardware on a wall that’s slightly out of plumb can make or break how the door swings and seals for the next ten years.
5 min read
Corner Frameless Enclosure with Chrome Hardware and Carrara-Look Marble — Milton, MA
This was a full corner enclosure — two glass panels meeting at 90 degrees with a hinged door on the front. The marble-look porcelain ran all the way up, and the homeowner went with polished chrome hardware to match the showerhead finish. The floor was small-format hex tile, which drains well and gives good footing. We set the door swing to open outward, which made sense given the layout, and the caulk line along the base came out clean against that white curb.
Large Walk-In Frameless Enclosure with Lighted Niche and Gray Tile — Newburyport, MA
This one in Newburyport was a big footprint — a proper walk-in with panels on both sides and a center door. The homeowner had a lighted niche built into the back wall with a decorative tile insert, which looked sharp once the glass was up and you could see everything through it. The tile was a large-format gray with a polished finish, and the chrome hardware complemented it without fighting for attention. Getting the panels plumb in a space that wide takes time, but it’s worth doing right so the door doesn’t bind or leave gaps at the sweep.
Walk-In Glass Panel with Green Subway Tile and Brass Fixtures — Chelmsford, MA
The green subway tile in this Chelmsford bathroom had real character — not a standard color, and the homeowner leaned into it with warm brass fixtures and a wood-tone vanity. We installed a fixed glass panel on one side and a return panel anchored to the half-wall, leaving an open entry. The micro-mosaic floor tile in white kept the floor from feeling heavy. This kind of open walk-in setup doesn’t use a door at all, so there’s no sweep seal to worry about — just the glass and the clamp hardware holding it in place. If you’re curious how those clamps work, here’s a closer look at the clamp systems we use on frameless installations.
Frameless Tub Door with Brushed Nickel Hardware and White Subway Tile — Salem, MA
This Salem job was a tub-shower combo — not a standalone shower — and the homeowner wanted to get away from a curtain rod and go with a fixed panel and swing door. White subway tile with dark grout ran floor to ceiling on three sides, and the hex tile floor had a classic black dot pattern that worked well with it. We used a drip rail along the bottom edge of the fixed panel to direct water back into the tub. The small window above the back wall was already there, and the glass clears it without blocking any light.
Matte Black Frameless Pivot Doors with Bold Geometric Accent Strip — Gloucester, MA
The Gloucester install was the most dramatic of this batch — dark charcoal large-format tile on the walls, a vertical geometric accent strip running floor to ceiling down the center, and matte black hardware throughout. It was a wide opening, so we used two full-height pivot doors that meet in the middle. The hex tile floor in light gray kept the floor from going too dark. The matte black finish on the clamps, hinges, and door pull ties everything together, and it’ll hold up well as long as the homeowner stays on top of drying the hardware after use — water sitting in the texture of a matte finish is where you start to see buildup over time.
Frequently Asked Questions
How do I keep frameless glass shower doors clean without streaks?
After every shower, run a squeegee from top to bottom and follow up with a dry microfiber cloth on the hardware. Once a week, spray the glass with a diluted white vinegar solution, let it sit for a minute, then wipe it down. That routine keeps hard water buildup from bonding to the surface before it becomes a problem.
When should I replace the sweep seal on my shower door?
If you’re finding water on the bathroom floor near the bottom of the door after a shower, take a close look at the sweep. If it’s cracked, flattened, or pulling away from the glass, it’s time to swap it out. Most sweeps last two to four years depending on how much the door gets used — our team can replace them when we’re in your area for any follow-up visit, so searching for frameless shower door service near me is a good place to start if you’re outside our usual route.
What does a custom frameless shower door cost on the North Shore?
Most of the jobs we do in the area — Danvers, Beverly, Salem, Marblehead — fall somewhere between $800 and $2,500 depending on the size of the opening, the hardware finish, and whether there’s a return panel or a fixed side. We offer free in-home measurements, which is the only real way to give you an accurate number because every bathroom is different.
We Work All Over the North Shore — Here’s Where to Find Us
Our team covers a wide stretch of eastern Massachusetts on a regular basis — Danvers, Beverly, Salem, Marblehead, Swampscott, Lynn, Peabody, and Middleton are all stops we make routinely, and we’re out on job sites every week. Spring is a busy stretch for us because a lot of homeowners are wrapping up bathroom projects before summer, and we’d rather get your measurement done now than have you waiting. If you’re ready to get moving, reach out to us here and we’ll get you on the schedule.
You can also call us directly at (978) 777-9900 — our team is ready to answer questions, talk through your layout, or set up a free in-home measurement at a time that works for you.
