Free shippingCRL fees on small ordersNot sure which seal? Try our Seal Finder →Hinge? Hinge Finder →
Shower Door Clear Vinyl Bulb Seal, 5/32" to 7/32" Gap (Pre-Taped) – CRL SDTBT2 profile drawing
CRL · Part SDTBT2In stock

Clear Vinyl Bulb Seal, 5/32" to 7/32" Gap (Pre-Taped)

Most popular hinge-side seal. The bulb compresses as the door closes.

$49.90 / 5-pack$9.98 each · sold in packs of 5
+ Free shipping
Sold in packs of 5. Our supplier only ships this seal in quantities of 5 or more, so each pack is 5 full lengths ($9.98 each).
5/32" to 7/32"Gap
95"Cut to fit
Peel & stickTape applied
Ships free to your doorFree to the lower 48 states and DC. Usually ships in 3–7 business days.
Plastic Trim Snips for Cutting Seals, Black – CRL PTS89 product photo
Cut it to lengthCRL PTS89 Plastic Trim Snips for Cutting SealsClean, straight or angled cuts on vinyl and plastic seals. $88.49
Free shippingLower 48 & DC
All sales finalCheck your glass thickness.
Not sure it fits?Try the Seal Finder
OverviewSpecsFAQGuides

About this seal

The CRL SDTBT2 is a 95-inch clear vinyl bulb seal, 5/32" to 7/32" gap (pre-taped), closing gaps 5/32" to 7/32". Made by C.R. Laurence (CRL); available in clear.

The flat base mounts to the glass edge or wall, and the hollow bulb squeezes shut as the door closes, sealing gaps from 5/32" to 7/32". Works on inswing or outswing doors. Comes with tape already applied: just peel and stick. 95" length, cut to fit. Sold in a minimum of 5.

  • Closes gaps 5/32" to 7/32"
  • Most popular for the hinge side
  • Inswing or outswing
  • Pre-applied tape
  • Minimum order: 5

Fit & specs

Glass thicknessAny
Gap5/32" to 7/32"
Door swingInswing or outswing
Installs byPeel and stick (tape applied)
Used forHinge or pivot side
Door against a wall
Latch (strike) side
Length95 in. (2413 mm)
MaterialVinyl
Pre-Applied TapeYes

Common questions

Does the SDTBT2 depend on glass thickness?

No. The SDTBT2 mounts to the glass edge or wall, so choose it by the gap it closes (5/32" to 7/32") rather than by glass thickness.

What gap does the SDTBT2 seal?

It closes gaps from 5/32" to 7/32". Measure with the door closed.

How do I install the CRL SDTBT2?

It comes with clear tape already applied: clean the surface, peel the liner and press it in place.

How do I cut the CRL SDTBT2 to length?

Measure the glass edge where the seal goes, then cut the seal to that length with plastic trim snips like the CRL PTS89 or a fine-tooth hacksaw. The snips give a clean, straight or angled cut in one squeeze.

How long is the SDTBT2?

It comes in a 95" length that you cut to fit your door.

Can I return the SDTBT2?

No. All sales are final: due to the nature of shipping these long seals, items cannot be returned. Measure your glass thickness and check the suggested gap before you order; our measuring guide shows how.

Finish the job

You may also need

Related guide

Shower Door Seal Keeps Falling Off? How to Fix It

A seal that keeps sliding or dropping off is almost always one of three things: it's made for a different glass thickness, the glass edge was dirty when it went on, or the tape on a stick-on seal has worn out..

Read the guide →