Neo-Angle and Corner Shower Door Seals (135° and 90°): Which to Buy and How to Replace Them
A corner shower needs seals shaped for its angle. A neo-angle door meets its angled panels at 135°; a square corner shower meets the fixed panel at 90°. Straight-line seals won't sit flat at either angle, so buy the seal made for yours.
Neo-angle (135°) shower seals
Leaking in a neo-angle (135°) shower
Answer: Buy two seals: a 135° door jamb seal for the hinge side and a 135° strike jamb seal for the angled panel on the latch side. Both pressure fit onto the glass and include a vinyl insert. Suggested gap 3/16".
| Your glass | Buy this exact part |
|---|---|
| 1/4" (6 mm) glass | No clip-on seal for this glass. Tape-on, fits any thickness: CRL P12LJT2 $18.90 Clear 'L' Jamb Stop 1/2" x 1/2" (Pre-Taped) CRL SDTS $26.25 / 5-pack Clear Vinyl 'V' Edge Seal, 3/16"–1/4" Gap |
| 5/16" (8 mm) glass | CRL P045DJ $25.18 135° Neo-Angle Door Jamb Seal for 5/16" Glass CRL P045SJ $37.78 135° Neo-Angle Strike Jamb Seal for 5/16" Glass |
| 3/8" (10 mm) glass, the most common | CRL P135DJ $29.38 135° Neo-Angle Door Jamb Seal for 3/8" Glass CRL P135SJ $35.68 135° Neo-Angle Strike Jamb Seal for 3/8" Glass |
| 1/2" (12 mm) glass | No clip-on seal for this glass. Tape-on, fits any thickness: CRL P12LJT2 $18.90 Clear 'L' Jamb Stop 1/2" x 1/2" (Pre-Taped) CRL SDTS $26.25 / 5-pack Clear Vinyl 'V' Edge Seal, 3/16"–1/4" Gap |
Other options:
- Rigid clear 'L' jamb stop, pre-taped, especially popular between the door and the angled panel (1/4"–1/2" glass): CRL P12LJT2 $18.90
- Tape-on 'V' edge seal, 3/16"–1/4" gap, for doors that swing one way: CRL SDTS $26.25 / 5-pack
We carry clip-on 135° jamb seals for 3/8" and 5/16" glass only. For 1/4" or 1/2" glass, use the tape-on options.
The strike jamb seal fits onto the angled panel the door closes against. That panel's edge is mitered (cut at an angle), and the seal is shaped to sit on that mitered edge.
90° corner shower seals
Leaking at a 90° corner, where the door meets a fixed panel at a right angle
Answer: Buy a 90° strike seal (with vinyl insert) or a clear 'U' with a 90° fin. It pressure fits onto the edge of the fixed panel the door closes against.
| Your glass | Buy this exact part |
|---|---|
| 1/4" (6 mm) glass | No clip-on seal for this glass. Tape-on, fits any thickness: CRL SDTL $28.90 / 5-pack Clear Vinyl 'L' Seal, up to 3/8" Gap CRL SDTNL $73.50 / 5-pack Clear Vinyl 'L' Seal, up to 5/16" Gap CRL P12LJT2 $18.90 Clear 'L' Jamb Stop 1/2" x 1/2" (Pre-Taped) |
| 5/16" (8 mm) glass | CRL PC0890 $33.58 Clear 'U' with 90° Fin Seal for 5/16" Glass |
| 3/8" (10 mm) glass, the most common | CRL P090SJ $31.48 90° Strike Seal with Vinyl Insert for 3/8" Glass CRL PC1090 $27.28 Clear 'U' with 90° Fin Seal for 3/8" Glass |
| 1/2" (12 mm) glass | No clip-on seal for this glass. Tape-on, fits any thickness: CRL SDTL $28.90 / 5-pack Clear Vinyl 'L' Seal, up to 3/8" Gap CRL SDTNL $73.50 / 5-pack Clear Vinyl 'L' Seal, up to 5/16" Gap CRL P12LJT2 $18.90 Clear 'L' Jamb Stop 1/2" x 1/2" (Pre-Taped) |
Other options:
- Tape-on 'L' seals for any glass thickness, by gap (outswing doors): up to 3/8" / up to 5/16": CRL SDTL $28.90 / 5-pack, CRL SDTNL $73.50 / 5-pack
- Rigid clear 'L' jamb stop, pre-taped, 1/4"–1/2" glass: CRL P12LJT2 $18.90
- 1/2" sliding door on the Essence system: 'U' with 90° soft leg: CRL PC1200 $29.38
We don't carry a clip-on 90° strike seal for 1/4" or 1/2" swing doors; on those, use one of the tape-on 'L' seals.
More on 90° leaks: shower leaking where the door meets the corner panel.
The bottom of the door
Corner and neo-angle doors still need a bottom wipe with drip rail: CRL P990WS for 3/8" glass, CRL P956WS for 5/16". Cut it to the full width of the door so water can't escape at the bottom corners.
Free shipping to the lower 48 states and DC. On small orders, CRL, the factory that makes these parts, adds its own packing or small-order fee, passed on at cost (see exceptions). All sales are final, so measure your glass first.
Replacing them, step by step
- Check the angle. Look at where the door closes. If the panel it closes against is angled (a neo-angle shower, usually fitted into a corner), it is 135°. If the panel meets the door at a right angle, it is a 90° corner.
- Measure the glass thickness. Lay a tape measure across a bare edge of the glass: corner and neo-angle doors are most often 3/8".
- Remove the old seals. Pull each seal off the glass edge, then clean the edges with rubbing alcohol.
- Cut to height. Measure each edge and cut the new seal to the same length with a fine-tooth hacksaw.
- Pressure fit. Press each seal onto its edge from top to bottom, with the vinyl insert facing the gap it seals.
- Test the door. The door should close against the seals without being pushed open. Check for drips at the bottom corners.
Door will not stay closed?
Magnetic seals give a glass door a positive close against a glass panel, with one strip on the door and one on the panel. See shower door won't stay closed for which pair to buy.
Browse every corner seal (90° and 135°).
Use our Seal Finder
Pick your door, point to where it leaks and we'll show only the seals that fit your glass. Takes about 30 seconds.
Products in this guide

135° Neo-Angle Door Jamb Seal for 3/8" Glass

135° Neo-Angle Strike Jamb Seal for 3/8" Glass

135° Neo-Angle Door Jamb Seal for 5/16" Glass

135° Neo-Angle Strike Jamb Seal for 5/16" Glass

90° Strike Seal with Vinyl Insert for 3/8" Glass

Clear 'U' with 90° Fin Seal for 3/8" Glass

Clear 'L' Jamb Stop 1/2" x 1/2" (Pre-Taped)
Most commonBottom Wipe with Drip Rail for 3/8" Glass
Common questions
What seals does a neo-angle shower door need?
A 135° door jamb seal on the hinge side and a 135° strike jamb seal on the latch side, plus a bottom sweep. For 3/8" glass: CRL P135DJ ($29.38) + CRL P135SJ ($35.68). For 5/16" glass: CRL P045DJ ($25.18) + CRL P045SJ ($37.78).
What angle is a neo-angle shower?
The door and the angled panels meet at 135°. That is why neo-angle doors need 135° jamb seals instead of straight 180° jambs.
What is the difference between a door jamb and a strike jamb seal?
The door jamb seal goes on the hinge side, the strike jamb seal on the latch side where the door closes against the angled panel.
What seal goes on a 90 degree corner shower?
On 3/8" glass, the CRL P090SJ ($31.48) 90° strike seal with vinyl insert, or the CRL PC1090 ($27.28) 'U' with a 90° fin, on the fixed panel edge the door closes against. On 5/16" glass, CRL PC0890 ($33.58). For 1/4" or 1/2" glass, use a tape-on 'L' seal such as CRL SDTL ($28.90 / 5-pack).
What corner seal fits 1/2" glass?
We don't carry a clip-on 90° or 135° jamb seal for 1/2" swing doors. Use the pre-taped CRL P12LJT2 ($18.90) 'L' jamb stop (fits 1/4"–1/2" glass) or a tape-on 'L' seal chosen by the gap.
Can I use 180° H-jambs on a neo-angle shower?
Not where the door meets an angled panel. A 180° jamb will not sit flat at 135° and will leak.
Is shipping free?
Shipping is free to the lower 48 states and DC. On small orders, CRL, the factory that makes these parts, adds its own packing or small-order fee, passed on at cost. All sales are final, so measure your glass first.